Things 3D Fila

aranha tarantula assustadora hairyetta

Criaturas

Se você ainda não tem uma máquina para imprimir este arquivo pode comprar uma impressora 3d aqui!

Você pode imprimir este modelo 3d com estes filamentos ou com estas resinas 3D.

Sobre o objeto 3D aranha tarantula assustadora hairyetta

Este é um arquivo desenvolvido e projetado com ferramenta CAD.

Se você ainda não sabe criar seu próprio modelo 3D eu te ensino neste artigo tutorial sobre Tinkercad.

aranha tarantula assustadora hairyetta foi projetado para Impressora 3D. update here is the place for the magnets for her legs to put them in use a small brush and put a little acetone in each of the holes on the legs then using a knife place a magnet on the knife and dip it in acetone hold dip and hold till it just melts itself into the hole and slide the knife to detach i have not installed the magnets for her inside as she is already glued together i only put a couple of drops of removable glue between body parts so i could take her apart when i got the magnets so it should not be to hardmagnets for feethttps://www.ebay.com/itm/N50-Mini-Round-Neodymium-Disc-Dot-Magnets-3x1mm-0-12x0-04-100pcs-Ship-from-US/132462261068?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649magnets for the body in retrospect i should have gotten longer magnets ? these are only 2mm deep but are the correct sizehttps://www.ebay.com/itm/US-Ship-20pcs-Round-Disc-Rare-Earth-Neodymium-Magnets-9-x-2mm-0-35x0-078-N50/122808039520?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649hairetta i wanted a female as they are more docile and less psychotic and live a lot loner than a malewent through 2 roles of error prints to make thisi had to repair a lot to make this thing printer friendlythis was a wonderful model but i had nothing but problems printing with warped parts not sticking to the bed and not printing the hairs because it looks like most are not even connected to the support and the legs are too loose to hold her up on her own and tons of errors in the stll files that xyzware could not fix or repair for proper printingalso i have split the files so there are less chances of printer problems and there are also parts that do not have hairs some tarantulas do not have all that hairand i did not want to have to set exact printing parameters for each part because xyzware does not allow any of the settings mentioned in the description so these are remade for the standard simple settings of xyzware with no supports to print the hairs print all the parts with the top door open on the xyz printer other printers have no in closer so this is not necessary for other printersi have added back the round parts of the legs they had ben cut flat on each side to allow for them to be put together so they are extremely tight to fit a lot of light pressure is required to snap them together one not to keep them from splitting when putting together all parts should be just dipped in acetone if using abs and the cups should be lightly filed so that both flat surfaces are flat and even and the round part should take a file and just a light filing to remove the widest part of the round about 3-4 passes no morethere are still loos parts like legs to the body to tighten all the loose fittings put a drop of paint into the joint you might have to do this a few times to take the gap out like on the but joint lots of play lots of paint drops

Baixar

Não deixe de imprimir e compartilhar este modelo 3d. Não deixe sua impressora 3D parada. Mas se você não tem uma impressora 3D ainda, escolha a sua agora.